Debian: Bootet sehr langsam (Futro S 210)

Hi,
schau mal in die Datei /var/log/boot ob da ein Fehler protokolliert ist.

wie kann ich das Lesen ?

less /var/log/boot 

folgender Text wird dann von “No” auf “Yes” umgeschrieben:

# Run bootlogd at startup ?
BOOTLOGD_ENABLE=Yes


Habe das oben erstmal gemacht, bin nun in diesem Menü und hab es auf yes geändert.

Kann es aber nicht speicher und beenden was muss ich drücken ? US Tastatur hab ich

welcher Editor?
 

Suche gerade wie verückt im verlauf was ich gemacht habe und finde die seite nicht mehr.

Hab glaub ich "vi" vorher eingetipt

vi /etc/default/bootlogd

Bei vi:

zum Einfügen / Schreiben die Einfügen(Insert-) Taste drücken
dann kannst du Ändern/Schreiben

Wenn fertig nacheinander zum Speichern drücken:
ESC   
:      (Doppelpunkt)
w
q

Wenn Du die Änderung nicht speichern willst:
ESC   
:      (Doppelpunkt)
q
!      (Ausrufezeichen)

Wenn Du eine US-Tastatur hast, entsprechend umrechnen.


 

Danke erstmal für die Hilfe
der editor hat sich aufgehängt als ich vor dem Fragen selbst probiert habe sämtliche tasten zu drücken.

Also nun ein neustart, dann alles neu eintippen und wieder ein neustart machen.

Bei dem zügigen bootvorgang denke ich nicht das ich heut nochmal poste, eher Morgen.
Also danke erstmal

Wenn Du bei vi in einen anderen Modus kommst, wo Du nicht weiterweisst oder irgendwas gedrückt hast, was Du eigentlich nicht wolltest - mit:

ESC
ESC   
:      (Doppelpunkt)
q
!      (Ausrufezeichen)

kommst Du ohne Speichern immer wieder raus

vi sieht auf den ersten Blick zwar spartanisch aus, ist aber sehr leistungsfähig und hat dadurch seine "Tücken"   

Hallo

sehe nur die letzte Minute in diesem log ?

 

.
Setting the system clock.
Activating Swap...done.
Checking root file system...fsck 1.41.3 (12-oct-2008)
/dev/hdc1: clean, 13411/231072 files, 99177/923729bl$
done.
Setting kernel variables (/etc/sysctl.conf?...done.
Mounting local filesystem...done.
Activating swapfile swap...done
Setting up networking....
Configuring network interface...done
Setting console screen modes and fonts
Init:entering runlevel:2
Starting enhanced syslogd: rsyslogd.
starting ACPI services...
Starting periodic command sheduler: crond.

Das sieht eigentl. ganz gut aus.

schau auch mal bitte in die /var/log/syslog
 

was hat den das Ding für einen Prozessor?

So steht es auf dem Bildschirm beim hochfahren:

 

Booting 'Debian GNU/Linux, kernel 2.6.26-2-486'

root (hd0,0)
 Filesystem type is ext2fs, partition type 0x83
kernel /boot/vmlinuz-2.6.26-2-486 root=/dev/hdc1 ro quiet
   [Linux-bzimage, setup=0x3000, size0x163b70]
initrd /boot/initrd.img-2.6.26-2-486

_  <--Blinkt!


Dann kommt lange nichts....mindestens 15 Minuten

Dann fängt er an richtig zu booten

[Linux-initrd @ 0x1e9f8ooo,0x5e7796 bytes]



Decrompressing Linux....Parsing ELF...done.
Booting the Kernel
[   0.653414] PCI: Cannot allocate resources

Allocating PCI reources starting$
PM:Registered nosave memory: 000$
PM:Registered nosave memory: 000$
PM:Registered nosave memory: 000$
PM:Registered nosave memory: 000$
Built 1 zonelists inzone order, $
Kernel command line:root=/dev/hd$
No local APIC present or hardware$
mapped APIC to ffffbooo (013e3000)
.....
.....
SELinux: Disabled at boot
....
....
ACPI: PCI Interrupt Routing Table$
ACPI: PCI Interrupt Link [LNKA] ($
ACPI: PCI Interrupt Link [LNKB] ($
ACPI: PCI Interrupt Link [LNKC] ($
ACPI: PCI Interrupt Link [LNKD] ($
Linux Plug and Play Support v0.97$
pnp: PnP ACPI init
ACPI: bus type pnp registred
pnp: PnP ACPI: found 12 devices
ACPI: ACPI bus type pnp unregistered$
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: Cannot allocate resources reg$
....

Detected 800,085 MHz processor

ruf mal den Befehl

 dmesg

auf und poste das Ergebnis

Hallo
hier der Text von dmesg, leider fehlt der anfang weil ich die | Taste nicht finde auf der Tastatur.


ext3_orphan_cleanup: deleting unreferenced imode 159398
EXT3-fs: hdc1: 1 orphan imode deleted
EXT3-fs: recovery complete
EXT3-fs: mounted filesystem with ordered data mode.
udevd version 125 started
input: PC Speaker as /class/input/input1
Linux agpgart interface v0.103
NET: Registered protocol family 23
input: ImPS/2 Generic Wheel Mouse as /class/input/input2
parport_pc 00:9: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778) irq 7 [PCSPP,TRISTATE]
ERROR: Driver 'pcspkr' is already registred, aborting
input: Power Button (FF) as /class/input/input3
ACPI: Power button (FF) [PWRF]
input: Power Button [CM] as /class/input/input4
ACPI: Power button (CM) [PBTN]
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC]-> GSI 10 (level, low) -> IRQ 10
[  157.105216] PCI: Setting latency timer of device 0000:00:11.5 to 64
[  160.885476] Adding 224868k swap on /dev/hdc5. priority:-1 extens:1 across:224868k
[  161.238260] EXT3 FS on hdc1, internal journal
[  162.076132] loop: module loaded
[  163.421978] eth0: link up, 100Mbps, full duplex, lpa 0x4DE1

leider fehlt der anfang weil ich die | Taste nicht finde auf der Tastatur.

wenn ich das drücke kommt so eine art doppelpunkt aber mit zwei langgezogenen strichen.

genau das isses!

[    1.538949] io scheduler anticipatory registered
[    1.538963] io scheduler deadline registered
[    1.539145] io scheduler cfq registered (default)
[    1.541972] isapnp: Scanning for PnP cards...
[    1.898662] isapnp: No Plug & Play device found
[    1.924211] Linux agpgart interface v0.103
[    1.926030] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.928117] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.928793] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.931716] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.932611] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.936558] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq1,12
[    1.937441] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.937512] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.938179] mice: PS/2 mouse device common for all mice
[    1.938875] rtc_cmos 00:03: RTC can wake from S4
[    1.939164] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    1.939609] rtc0: alarms up to one year, y3k, 242 bytes nvram
[    1.940784] EISA: Probing bus 0 at eisa.0
[    1.940934] Cannot allocate resource for EISA slot 1
[    1.941707] EISA: Detected 0 cards.
[    1.941729] cpuidle: using governor ladder
[    1.941753] cpuidle: using governor menu
[    1.941938] No iBFT detected.
[    1.945872] TCP cubic registered
[    1.946801] NET: Registered protocol family 10
[    1.954710] Mobile IPv6
[    1.954755] NET: Registered protocol family 17
[    1.954822] Using IPI Shortcut mode
[    1.955650] PM: Resume from disk failed.
[    1.955794] registered taskstats version 1
[    1.958491] rtc_cmos 00:03: setting system clock to 2011-08-09 01:25:52 UTC 1312853152)
[    1.958833] Initalizing network drop monitor service
[    1.959434] Freeing unused kernel memory: 444k freed
[    1.963813] Write protecting the kernel text: 2340k
[    1.964332] Write protecting the kernel read-only data: 880k
[    1.965993] input: AT Translated Set 2 keyboard as /devices/platform/i8042/srio0/input/input0
[    2.605715] udev[44]: starting version 164
[    4.298658] SCSI subsystem initialized
[    4.358220] usbcore: registered new interface driver usbfs
[    4.359529] usbcore: registered new interface driver hub
[    4.360778] usbcore: registered new device driver usb
[    4.401902] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.403546] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
[    4.403578] PCI: setting IRQ 10 as level-triggered
[    4.403612] ehci_hcd 0000:00:10.3: PCI INT D -> Link[LNKD] -> GSI 10 (level,low) -> IRQ 10
[    4.403780] ehci_hcd 0000:00:10.3: EHCI Host Controller
[    4.404164] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus numbr 1
[    4.405081] ehci_hcd 0000:00:10.3: irq 10, io mem 0x20010000
[    4.493536] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00
[    4.494682] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    4.494706] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber1
[    4.494722] usb usb1: Product: EHCI Host Controller
[    4.495001] usb usb1: Manufacturer: Linux 2.6.32-5-486 ehci_hcd
[    4.495014] usb usb1: SerialNumber: 0000:00:10.3
[    4.501810] usb usb1: configuration #1 chosen from 1 choice
[    4.504131] hub 1-0:1.0: USB hub found
[    4.505026] hub 1-0:1.0: 6 ports detected
[    4.536637] libata version 3.00 loaded.
[    4.561158] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[    4.562618] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
[    4.562660] via-rhine 0000:00:12.0: PCI INT A -> Link[LNKA] -> GSI 10 (level low) -> IRQ 10
[    4.609867] eth0: VIA Rhine II at 0x1e200, 00:90:dc:03:39:84, IRQ 10.
[    4.611101] eth0: MII PHY found at address 1, status 0x786d advertising 05e1Link 41e1.
[    4.636443] pata_via 0000:00:11.1: version 0.3.4
[    4.636601] pata_via 0000:00:11.1: PCI INT A -> Link[LNKA] -> GSI 10 (level,low) -> IRQ 10
[    4.636632] pata_via 0000:00:11.1: VIA VLink IRQ fixup, from 0 to 10
[    4.642400] scsi0 : pata_via
[    4.643532] scsi1 : pata_via
[    4.666582] uhci_hcd: USB Universal Host Controller Interface driver
[    4.677782] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x1100 irq 14
[    4.677811] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1108 irq 15
[    4.683755] uhci_hcd 0000:00:10.0: PCI INT A -> Link[LNKA] -> GSI 10 (level,low) -> IRQ 10
[    4.683841] uhci_hcd 0000:00:10.0: UHCI Host Controller
[    4.683982] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus numbr 2
[    4.684222] uhci_hcd 0000:00:10.0: irq 10, io base 0x00001200
[    4.686391] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    4.686416] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber1
[    4.686430] usb usb2: Product: UHCI Host Controller
[    4.686443] usb usb2: Manufacturer: Linux 2.6.32-5-486 uhci_hcd
[    4.686454] usb usb2: SerialNumber: 0000:00:10.0
[    4.696216] usb usb2: configuration #1 chosen from 1 choice
[    4.697299] hub 2-0:1.0: USB hub found
[    4.697763] hub 2-0:1.0: 2 ports detected
[    4.704686] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
[    4.704716] PCI: setting IRQ 5 as level-triggered
[    4.704746] uhci_hcd 0000:00:10.1: PCI INT B -> Link[LNKB] -> GSI 5 (level, ow) -> IRQ 5
[    4.704779] uhci_hcd 0000:00:10.1: VIA VLink IRQ fixup, from 10 to 5
[    4.704866] uhci_hcd 0000:00:10.1: UHCI Host Controller
[    4.706935] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus numbr 3
[    4.707101] uhci_hcd 0000:00:10.1: irq 5, io base 0x00001220
[    4.708812] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    4.708834] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber1
[    4.708847] usb usb3: Product: UHCI Host Controller
[    4.708860] usb usb3: Manufacturer: Linux 2.6.32-5-486 uhci_hcd
[    4.708871] usb usb3: SerialNumber: 0000:00:10.1
[    4.720506] usb usb3: configuration #1 chosen from 1 choice
[    4.728192] hub 3-0:1.0: USB hub found
[    4.728321] hub 3-0:1.0: 2 ports detected
[    4.731353] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[    4.731399] uhci_hcd 0000:00:10.2: PCI INT C -> Link[LNKC] -> GSI 10 (level,low) -> IRQ 10
[    4.731476] uhci_hcd 0000:00:10.2: UHCI Host Controller
[    4.731918] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus numbr 4
[    4.748310] uhci_hcd 0000:00:10.2: irq 10, io base 0x00001240
[    4.750598] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    4.750623] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber1
[    4.750638] usb usb4: Product: UHCI Host Controller
[    4.750651] usb usb4: Manufacturer: Linux 2.6.32-5-486 uhci_hcd
[    4.750662] usb usb4: SerialNumber: 0000:00:10.2
[    4.764503] usb usb4: configuration #1 chosen from 1 choice
[    4.768213] hub 4-0:1.0: USB hub found
[    4.768345] hub 4-0:1.0: 2 ports detected
[    5.015941] ata2.00: CFA: SMI MODEL, 20091113, max UDMA/66
[    5.015973] ata2.00: 7847280 sectors, multi 0: LBA
[    5.016337] ata2.00: limited to UDMA/33 due to 40-wire cable
[    5.025454] ata2.00: configured for UDMA/33
[    5.028215] scsi 1:0:0:0: Direct-Access     ATA      SMI MODEL        2009 P: 0 ANSI: 5
[    5.127166] sd 1:0:0:0: [sda] 7847280 512-byte logical blocks: (4.01 GB/3.74GiB)
[    5.135420] sd 1:0:0:0: [sda] Write Protect is off
[    5.135450] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    5.138670] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, dosn't support DPO or FUA
[    5.178669]  sda:
[   35.816451] ata2: lost interrupt (Status 0x50)
[   35.816930] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[   35.817103] ata2.00: failed command: READ DMA
[   35.817235] ata2.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 n
[   35.817246]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeut)
[   35.817478] ata2.00: status: { DRDY }
[   35.818597] ata2: soft resetting link
[   35.996556] ata2.00: configured for UDMA/33
[   35.996791] ata2.00: device reported invalid CHS sector 0
[   35.996953] ata2: EH complete
[   66.816130] ata2: lost interrupt (Status 0x50)
[   66.816498] ata2.00: limiting speed to UDMA/25:PIO4
[   66.816538] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[   66.816841] ata2.00: failed command: READ DMA
[   66.817081] ata2.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 n
[   66.817090]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeut)
[   66.818336] ata2.00: status: { DRDY }
[   66.819126] ata2: soft resetting link
[   67.002604] ata2.00: configured for UDMA/25
[   67.002779] ata2.00: device reported invalid CHS sector 0
[   67.002930] ata2: EH complete
[   97.816134] ata2: lost interrupt (Status 0x50)
[   97.816327] ata2.00: limiting speed to PIO4
[   97.816362] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[   97.816513] ata2.00: failed command: READ DMA
[   97.816634] ata2.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 n
[   97.816642]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeut)
[   97.817171] ata2.00: status: { DRDY }
[   97.818530] ata2: soft resetting link
[   98.006416] ata2.00: configured for PIO4
[   98.006489] ata2.00: device reported invalid CHS sector 0
[   98.006634] ata2: EH complete
[   98.089286]  sda1 sda2 < sda5 >
[   98.097927] sda: detected capacity change from 0 to 4017807360
[   98.111999] sd 1:0:0:0: [sda] Attached SCSI disk
[   98.123071] sda: detected capacity change from 0 to 4017807360
[   98.762654] PM: Starting manual resume from disk
[   98.762691] PM: Resume from partition 8:5
[   98.762699] PM: Checking hibernation image.
[   98.767172] PM: Error -22 checking image file
[   98.767197] PM: Resume from disk failed.
[   98.904659] kjournald starting.  Commit interval 5 seconds
[   98.905321] EXT3-fs: mounted filesystem with ordered data mode.
[  101.257370] udev[247]: starting version 164
[  102.966476] Marking TSC unstable due to TSC halts in idle
[  102.978883] processor LNXCPU:00: registered as cooling_device0
[  103.000483] Switching to clocksource acpi_pm
[  103.128715] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:0/input/input1
[  103.129781] ACPI: Power Button [PBTN]
[  103.130340] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/inut2
[  103.130422] ACPI: Power Button [PWRF]
[  103.592399] NET: Registered protocol family 23
[  103.593685] input: PC Speaker as /devices/platform/pcspkr/input/input3
[  103.866212] parport_pc 00:09: reported by Plug and Play ACPI
[  103.866336] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[  104.148476] psmouse serio1: ID: 10 00 64
[  104.478581] ACPI: I/O resource vt596_smbus [0x1400-0x1407] conflicts with ACI region SM06 [0x1406-0x1406]
[  104.478786] ACPI: If an ACPI driver is available for this device, you shoulduse it instead of the native driver
[  104.647355] Error: Driver 'pcspkr' is already registered, aborting...
[  104.857699] VIA 82xx Audio 0000:00:11.5: PCI INT C -> Link[LNKC] -> GSI 10 (evel, low) -> IRQ 10
[  104.858013] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
[  104.865808] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/sero1/input/input4
[  106.445865] Adding 224868k swap on /dev/sda5.  Priority:-1 extents:1 across:24868k
[  106.766532] EXT3 FS on sda1, internal journal
[  107.103460] loop: module loaded
[  108.505362] eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
[  118.904057] eth0: no IPv6 routers present
debian:~#


Hab es doch geschafft durch ein update debian6 drauf zu bekommen was ich ursprünglich wollte siehe post 1.
Jetzt braucht er über eine Stunde zum hochfahren ?
Findet er sein einstiegspunkt nicht ?

[    5.138670] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, dosn't support DPO or FUA
[    5.178669]  sda:
[   35.816451] ata2: lost interrupt (Status 0x50)
[   35.816930] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[   35.817103] ata2.00: failed command: READ DMA

oder USB-Platte

Hallo

ja man kann eine HDD anschliessen.
Habe momentan keine andere platte, muss ich kaufen.

Die CF card im Rechner ist neu gewesen hatte ich extra gekauft für den futro.

Der eingebaute CF-Cardslot kann kein DMA und ist deswegen extrem langsam. Hinzu kommt, dass das Linux einige Zeit braucht, um das zu erkennen. Ich verwende in meinem Futro einen UDMA kompatiblen CF-IDE Adapter an der IDE Schnittstelle. hdparm benchmark ~30MB/s